收藏本站
ALUMINUM ELECTROLYTIC CAPACITORS
the dropped capacitor.
? Do not deform the capacitor for mounting.
2. Do not apply excessive pressure to the capaci-
tor, its terminals or lead wires.
? Make sure that the contact path of the capacitor
meets the hole pitch of the PCB before mounting.
? Transient recovery voltage may be generated in the
capacitor due to dielectric absorption. If required,
this voltage can be discharged with a resistor with
a value of about 1 k Ω .
? A PCB self-standing (snap-in) type capacitor should
be pushed to the end (till there is no space) to the
PCB for mounting.
? Do not set the automatic insertion machine to clinch
the capacitor lead wires too strong.
? Pay attention to the impact given by the compo-
nent receptacles of the automatic insertion/mount-
ing machines and the product checker, and from
the centering operation.
3. Soldering.
? Do not dip the capacitor into melted solder.
? The soldering conditions
Chip type : Please refer to 11 page.
small and large type : 260°C, 10 s (max.)
The preliminar y heating and other conditions
described in the catalog or product specifications.
? Do not flux other part than the terminals.
? If there is a direct contact between the sleeve of
the capacitor and the printed circuit pattern or a
metal part of another component such as a lead
wire, it may cause shrinkage of crack.
? When you use the capacitor with its sleeve touch-
ing directly to the PCB, excessive solder tempera-
ture or excessive soldering time may cause the
sleeve to shrink or crack during the heat.
? If the application is for extended use, understand
and manage the soldering characteristics to avoid
abnormal current caused by a contact failure
between the capacitor and the PCB.
4. Handling after soldering.
? After soldering, do not tilt, push down or twist the
capacitor.
? After soldering, do not hold the capacitor as a
handle to carry the PCB.
? After soldering, do not hit the capacitor with any
obstacle. If PCB ’s are piled up for storage, the
capacitor should not touch another PCB or compo-
?
(2)Cleaning conditions:
(a) The temperature of cleaning solution shall be
less than 60°C.
(b) Use immersion or ultrasonic waves within two
minutes.
(c) After cleaning, capacitors and PCB ’s shall
thoroughly be rinsed and dried with hot blast
for more than 10 minutes. The temperature of
such breeze should be less than the upper
category temperature.
(d) After cleaning, do not keep capacitors in
cleaning solution atmosphere or air tight
containers.
? During cleaning, control the cleaning solution
against contamination.
6. Fixing adhesives and coating materials.
? Do not use fixing adhesive or coating material
containing halogen-based solvent.
? Before applying the fixing adhesive or the coating
material, make sure that there is no remaining flux
or stains between the PCB and the sealed part of
the capacitor.
? Before applying the fixing adhesive or the coating
material, make sure that the detergent etc. has
dried up.
? Do not cover the whole surface of the sealed part
(terminal side) of the capacitor with the fixing ad-
hesive or the coating material.
? Observe the description in the catalog or the prod-
uct specifications concerning the thermal stiffening
conditions of the fixing adhesive or the coating
material. (If there is no such description, contact
us.) When both discrete and SMT components are
on the same PCB, the fixing material for the SMT
components may cause crack, tear or shrinkage on
the external sleeve depending on the thermal
stiffening condition.
? Recommended fixing adhesives and coating
materials
Fixing adhesives : Cemedine 210, 501, 540, 545N, Diabond
DN83K, DA3288, Bond G103
Coating materials : Taffy TF1159, HumiSeal 1B66, 1A27NS
Other Cautions
1. Do not touch capacitor terminals with bare hands.
You may get electric shock or your hand may be
burnt. Discharge it with a 1 K Ω resistance before use
if necessary.
nent.
2. Do not short the capacitor terminals with a con-
5. Cleaning after Soldering
? Recommended cleaning method
(1)cleaning solutions:
(a) CLEANTHROUGH 710M, 750H, 750L
(b) PINEALPHA ST-100S
(c) Techno Care FRW-4~17
(d) Isopropyl alcohol (2-propanol)
CAT.No.2008/2009E(2008.10.1)
ductor.
Do not spill conductive solution including acid or alka-
line solution on the capacitor.
3. Periodical inspections should be established
for the capacitors used in industrial appliances.
? The following items should be checked:
NOTE
Design, Speci?cations are subject to change without notice.
Ask factory for technical speci?cations before purchase and/or use.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DCMC103T450FN2D CAP ALUM 10000UF 450V SCREW
DD12.6123.111 DD12 POWER ENTRY MOD W/FLTR 6A
DD22.9321.1111 POWER ENT MOD W/FILTR 10A M5 2PL
DE1E3KX332MA5BA01 CAP CER 3300PF 250V 20% RADIAL
DEBB33F222KA3B CAP CER 2200PF 3.15KV RADIAL
DEH-15-0001 DEH GROUND WIRE CHOKE 25A
DEHR33D472KB4B CAP CER 4700PF 2KV 10% RADIAL
DEHR33F182KA3B CAP CER 1800PF 3.15KV RADIAL
相关代理商/技术参数
DCK-3R3D224 功能描述:超级电容/超级电容器 SMT 3.3V 0.22F RoHS:否 制造商:Murata 电容:350 mF 容差: 电压额定值:4.2 V ESR:60 mOhms 工作温度范围:- 30 C to + 70 C 端接类型:SMD/SMT 引线间隔: 尺寸:18.5 mm W x 20.5 mm L x 3 mm H
DCK-3R3E204T614-E 功能描述:CAP SUPER 200MF 3.3V COIN SMD RoHS:是 类别:电容器 >> 双电层，超级电容器 系列:DCK 产品培训模块:PowerStor Supercapacitors 产品变化通告:KSL, KSR Series Obsolescence 2/Jun/2010 标准包装:1 系列:PowerStor® KSR 电容:200mF 电压 - 额定:3.3V 容差:-20%，+80% ESR（等效串联电阻）:200 欧姆 寿命@温度:60°C 时为 1000 小时 安装类型:表面贴装 封装/外壳:币形，细型端子 - 同侧 引线间隔:- 包装:Digi-Reel® 尺寸/尺寸:0.268" 直径（6.80mm） 高度 - 座高（最大）:0.071"（1.80mm） 工作温度:-10°C ~ 60°C 其它名称:283-2859-6
DCK-3R3E224U-E 功能描述:CAP SUPER 220MF 3.3V COIN SMD RoHS:是 类别:电容器 >> 双电层，超级电容器 系列:DCK 产品培训模块:PowerStor Supercapacitors 产品变化通告:KSL, KSR Series Obsolescence 2/Jun/2010 标准包装:1 系列:PowerStor® KSR 电容:200mF 电压 - 额定:3.3V 容差:-20%，+80% ESR（等效串联电阻）:200 欧姆 寿命@温度:60°C 时为 1000 小时 安装类型:表面贴装 封装/外壳:币形，细型端子 - 同侧 引线间隔:- 包装:Digi-Reel® 尺寸/尺寸:0.268" 直径（6.80mm） 高度 - 座高（最大）:0.071"（1.80mm） 工作温度:-10°C ~ 60°C 其它名称:283-2859-6
DCK413S2 制造商:Dewalt 功能描述:12 Volt Max Lithium-Ion 4-Tool Combo Kit 制造商:DEWALT 功能描述:12V MAX 4 TOOL KIT RECIP IMPACTOR DRILL LIGHT
DCK4A-CA 制造商:Leviton Manufacturing Co 功能描述:
DCK590L2 制造商:Dewalt 功能描述:20V MAX Lithium Ion 5-Tool Combo Kit
DCK-703S 制造商:SYNERGY 制造商全称:SYNERGY MICROWAVE CORPORATION 功能描述:POWER DIVIDERS 0ì : 3-WAY
DCK-7D3 制造商:SYNERGY 制造商全称:SYNERGY MICROWAVE CORPORATION 功能描述:POWER DIVIDERS 0ì : 3-WAY